The Metric Nut VW 22 views Claim this Business♡

These top gearbox mounts fit all VW Kombi's from 1972 to 1979

CV Joint Flange Grease Cap

Gearbox gasket set.Includes all of the main seals and gaskets.Suits Kombi Gear Box 1968 to 1975Made by Erling of Germany 

Type 3 Drive Shaft complete Automatic only Left Hand SideEMPI's drive axle assemblies are assembled from all new top quality components manufactured by EMPI, and come complete ready to installWe have tested these and they are top quality.Sold each

Type 3 Drive Shaft complete Automatic only Right Hand SideEMPI's drive axle assemblies are assembled from all new top quality components manufactured by EMPI, and come complete ready to installWe have tested these and they are top quality.Sold each

VW Kombi Drive Shaft 1968 to 1979 for manual transmission Kombi's only.These drive axle assemblies are assembled from all new top quality components, and come complete ready to installWe have tested these and they are top quality, and far superior to the "Classic" brand from supposed "Denmark" Sold each

Refurbished Bosch Starter motor.

Vintage Speed Exhaust Kombi 1968 and on with heat risers for single carb set ups.High Performance Stainless Steel Muffler for 1968 and on Kombi's with Type 1 Engines.Comes with heat exchanger clampsFeatures:1. ± 4mm Adjustable flanges for stroker or narrower engines.2. Muffler is 1.5" higher than e...

Replacement

Lift 430, Duration 284.Hot street & off road, good low midrange power, fair idle.Engle aftermarket performance cams for aircooled VW Volkswagen have been the racing industry standard for over 50 years. When choosing a camshaft, determine the engine size, desired power band and compression ratio....

This is a great kit to fit to any performance Air Cooled Engine.This Deluxe EMPI Hex Bar HPMX Carburetor Kit features an aluminum alloy hex bar with steel ball ends, sealed aircraft heim rod ends, ball burnished / polished offset aluminum intake manifolds, heavy duty aluminum manifold castings with ...

Being New Zealand's Official Vintage Speed re-seller for the last 10 Years, we have the knowledge on the best muffler for your vehicle, so if you have any questions feel free to.Vintage Speed Stainless steel Exhaust for Beetle and Karmann Ghia's suits all 1300 to 1600 based engines, will also fits l...

Save weight and add performance with EMPI's forged 4340 Chromoly H-Beam Connecting Rods. With a length of 5.400 inches and Chevy Journals of 2.000inch/51mm, these H-Beam Connecting Rods are made to fit with EMPI's stroker cranks. Sets of four are sold in matching weight and have a recommended torque of 26 ft. lbs.

These are the longer 5.4" length rod good for the 76mm stroker crank shaft in a type 1 based engine.H Beam rods are a must for any performance or none stock engine build.Rods have the small end bush fitted and reamed ready for use.Also supplied is the ARP forged bolts capable of withstanding 220,000 Psi tensile loads.Set of 4

1200-1600cc Main Bearings Set, Steel backed for extra strength , these bearings are a excellent bearing for any rebuild on a line bored case.Bearing sizes in this set.040" (1.0mm) Case030" (.75mm) Crank1.0mm Flange

Works with Dual Port Style Type 1 Engines.This is the inlet manifold you need when you old inlet has blocked heat riser pipes and your carb ices and also when converting to twin port heads on your engine.Don't forget the boots that seal to the inlets also available from us.We have found fitting these that they can need adjustments to work and fit well.

Only For VW Air-cooled Engines. 

Flywheel Shim, 1300 to 1600cc style engines, 0.34mmThis is used to take up the excessive gap between the main bearing and flywheel, often referred to as end float. By using shims of different thicknesses, you can set the gap to spec 0.10mm (.005") to minimize bearing and case wear.

Flywheel Shim, 1300 to 1600cc style engines, 0.32mmThis is used to take up the excessive gap between the main bearing and flywheel, oftern refered to as end float. By using shims of different thicknesses, you can set the gap to spec 0.10mm (.005") to minimize bearing and case wear.

Flywheel Shim, 1300 to 1600cc style engines, 0.36mmThis is used to take up the excessive gap between the main bearing and flywheel, oftern refered to as end float. By using shims of different thicknesses, you can set the gap to spec 0.10mm (.005") to minimize bearing and case wear.

Heavy Duty Cross Shaft, Shaft ONLYFits 1971 to 1975 VW Kombi's with the 3 rib 002 style gearbox that runs the late stye release bearing.This directly replaces worn-out and weak stock units.HD Clutches can really stress stock pieces, we strongly recommend this upgrade, especially when using HD Pressure Plates

Pressure plate stage 1 1700lb 200mm, is a good plate to fit to any Mild, Offroad or High performance street applications.These 200mm pressure plates are rated at 1700lbs and are factory balanced.Will work with early and late style release bearings, as you can remove the centre pad to convert the set up for that later release bearing

Pressure plate stage 1 Kennedy 1700lb 200mm, is a good plate to fit to any Mild, Offroad or High performance street applications.These 200mm pressure plates are rated at 1700lbs and are factory balanced.Will work with early and late style release bearings, as you can remove the centre pad to convert the set up for that later release bearing

Probably the most popular high performance clutch disc for the last 20 years! The brass woven lining really takes the heat. 200mm with steel riveted hub and triple "sandwich" center for smooth Kush Lock action.