Rapid Performance 1 views Claim this Business♡

Connector kit to suit GM crank sensorIncludes plug, pins, and latch

Connector kit to suit Nissan VQ Cam Position Sensor (green, bank 1)includes plug, pins, and latch

HT-010134Includes: Matching male Deutsch DTM-3 Connector (HT-031001)3 Bar Motorsport MAP Sensor

HT-010136Includes: Matching male Deutsch DTM-3 Connector (HT-031001)4 Bar Motorsport MAP Sensor

HT-010200Includes: Matching Delphi plug and pins.Notes: 127 deg C (260 F) Max reading.Air Temp Sensor - Small Thread M14 x 1.5

HT-010230Suits: Air Temp Sensor - Small Thread.Weld Fitting M14 x 1.5 - Small Thread Air Temp Aluminum

HT-010610Suits: Wheel Speed, Crank/Cam.Includes: Matching set of Deutsch DTM 3 connectors (HT-031014)"Red" Single Channel Hall Effect Sensor M12x1.0

HT-010609Suits: Wheel Speed, Crank/Cam.Includes: Matching set of Deutsch DTM 3 connectors (HT-031014)GT101 Style High Frequency Hall Effect Sensor

HT-011100Suits: 8mm (5/16") mounting bolt.Includes: Matching plug and 2 pins.Knock Sensor - Genuine Bosch

HT-011601Suits: Haltech Nexus and Elite ECU's using NSP and ESP SoftwareIncludes: 1 x Haltech TMS-4 Reciever 1 x TE Mcon to DTM-4 CAN Cable 4 x External Sensors 4 x anti-theft lock nuts Lock Nut spanner Mounting Hardware Quick Start GuideNotes: Batteries for external sensors are included and are rep...

HT-011600Suits: Haltech Nexus and Elite ECU's using NSP and ESP SoftwareIncludes: 1 x Haltech TMS-4 Reciever 1 x TE Mcon to DTM-4 CAN Cable 4 x Internal Sensors Warning Sticker Set Mounting Hardware Quick Start GuideNotes: Batteries for internal sensors are included and are NOT replaceable Typical l...

Honeywell 2000psi pressure sensor with 1/8 NPT port2000psi gauge pressureideal for use as Brake or clutch pressure sensor0.5V to 4.5V output, 5V activation voltageStainless steel lower housing

Stainless 10-bar (~145psi) pressure sensor with 1/8"NPT PortMedia isolated sensorsuitable for use with water, petrol, diesel, hydraulic fluids, CNGStainless constructionIdeal for measuring fuel and oil pressure3-Way Metri-Pack 150 electrical connectionRated from -40ºC to 125ºC - ideal for oil pres...

Stainless steel 60psi absolute pressure sensor with 1/8"NPT PortMedia isolated sensorsuitable for use with water, petrol, diesel, hydraulic fluids, CNGStainless constructionIdeal for measuring boost in high booost applicaitons3-Way Metri-Pack 150 electrical connectorRated from -40ºC to 125ºCSupply voltage from 4.75V to 5.25V0.5V to 4.5V Output voltage22mm hex

-Sensor Electrical Connector:Bosch Trapez 5-WaySensor-Type:Fluid Pressure and TemperatureMeasurement Range:-40 to 140 degrees C and 0 to 10 bar (145 psi)Mechanical-Connection:M10 x 1 male thread

Allow weld on fitting to suit 1/8 npt air temp sensors

NTC air temperature sensor with 1/8" NPT thread and Deutsch 2-way electrical connector.Uses the same calibration as Delco air temperature sensors.Suitable for use with most aftermarket engine management systems including Motec, Life Racing, Syvces, Link, Haltech, Emtron and many others

The NTC sensing element has a negative temperature coefficient. This means, that with increasing temperature the conductivity rises. The sensing element of the temperature sensor is made of semiconducting heavy metal oxide and oxidized mixed crystals, which are equipped with a protective housing. M1...

NZ wiring cam trigger kit to suit rb20 / rb25 / rb26 / rb30 / ca18 twin cam engines. This kit replaces the factory cam angle sensor that is prone to outputting an inaccurate signal on modified engines. Supplied with a 300mm wiring tail and Deutsch connector, so that the join can be tucked around the cold side of your rocker cover.Note: cannot be used with factory Nissan ecu

Tired of misfire/distributor issues with your Honda B series engine? If so our coil-on plug kit is for you.With OEM B series distributors becoming hard to get, and the aftermarket distributors not lasting particularly well on engines used for racing, a coil-on plug ignition setup is by far the best ...

Rapid Performance gtr speed input kit:Our new r32-r33-r34 gtr speed input kits are finished and ready to send. These are ideal for customers wanting to run a Haltech ic-7 dash (or similar) and needing a reliable speed signal. Especially handy on r32 models, which have a cable driven speedo from fact...

In early model Nissans (R32, R33, S13, S14 ), and also some other vehicles, the factory fuel pump wiring is of poor quality and goes through many joins. This results in fuel pump voltage being down around 10.5v, even when battery voltage is 13v. High flow fuel pumps do not work well at this low volt...

Reed switch with magnet. These are mounted to the clutch pedal, and used as an ecu input to momentarily cut the engine during no-lift gear shifting

High quality TXL wire as used by many OEM's, this is a cost effective wire that's easy to work with. Perfect for your next wiring harness build. Sold per metre.12awg