Full Throttle 1 views Claim this Business♡

Part Number: 226-4000Easy to install. Affordable. Reliable. G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car. This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring lo...

Part Number: 227-4000Easy to install. Affordable. Reliable. G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car. This ECU fits inside the factory OEM enclosure. Installation is a breeze, with no alteration of the factory wiring lo...

Part Number: 127-4000MonsoonX More features, more powerful. The MonsoonX has been upgraded to provide 512 megabytes of data logging, meaning you can log much more data at a faster sample rate. Control loops are also more precise compared to its G4 predecessor, along with advancements such as single ...

Part Number: 135-1000Link's highly anticipated PDM, the Razor PDM, is an intelligent Power Distribution Module that replaces traditional fuses and relays, putting you in complete control of your setup. The Razor PDM is a programmable device that uses logic for the smart control of any outputs you ha...

Part Number: 111-4000AtomX Small, but mighty! The the latest version of our entry-level ECU. Don't let its size fool you however, the AtomX has expanded data logging and uses the same microcontroller as the entire G4X range! It is more responsive and has higher bandwidth than its G4 Atom II predeces...

Part Number: 101-0226The Link CAN Gauge is a compact OLED gauge for displayingreal-time data from your Link ECU’s CAN stream. Supported parameters such asboost pressure, air/fuel ratio, coolant temperature, fuel pressure, ethanolcontent,. can be displayed. The high contrast OLED display is bright ...

Part Number: 125-1000Link’s CAN Lambda is an easy to use CAN module that provides digital wideband sensor control via CAN bus and is compatible with leading aftermarket ECUs. If using the CAN Lambda with a G4 /G4X PlugIn ECU use a Link CANPCB cable to access the CAN port on the PlugIn PCB and a Li...

Part Number: 101-0298The 8 Bar MAP Variohm Eurosensor reads up to 7 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 7 Bar (or 101psi) of boost pressure. Includes Plug and Pins Push wire through connector; crimp on terminal; pull wire/termina...

Part Number: 101-0034Looking to run flex-fuel? Then the Ethanol Content Sensor is a must have. The Ethanol Content Sensor measures the ratio of ethanol to petrol in a flex fuel vehicle. This sensor also measures fuel temperature. Compatible with all current Link Wire-In and Plug-In ECU’s. Uses 1 D...

Part Number: 101-0080Oil or Fuel pressure 10 Bar/150psi 1/8" NPT Thread Includes plug and pin kit Technical Specs and Wiring Up to 150 PSI above atmospheric pressure, cannot be used to read vacuum 0.5v = 0bar / 0PsiG 4.5v = 10 Bar / 145.03PsiG

Part Number: 114-1000KnockLink is a self-calibrating, visual knock warning tool. The KnockLink is designed for tuning, street and race use. Will require a knock sensor to function (sold separately) or you can purchase the KnockLink Kit that includes the Knock Sensor and Loom. The G4 KnockLink is the...

Part Number: 101-0295The 5 Bar MAP Variohm Eurosensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 4 Bar (or 58psi) of boost pressure. Includes Plug and Pins Push wire through connector; crimp on terminal; pull wire/terminal...

Part Number: 101-0116This sensor can be used with all wide band controllers and ECU’s that support LSU 4.9 sensors. This includes: Link G4 /G4X Fury and G4 Thunder ECU’s – These have on-board LSU4.9 wide-band control. Link CAN-Lambda Controller – These are sold new with a sensor, so this sen...

Part Number: 101-0165The Link 4 Bar MAP sensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 3.0 Bar (or 44psi) of boost pressure. The wiring pinout for this sensor is marked directly on the sensor. Includes 3-pin Deutsch DTM...

Part Number: 101-0164This Link MAP sensor reads up to 3 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 2.0 Bar (or 29psi) of boost pressure. The wiring pinout for this sensor is indicated on the sensor. Includes Deutsch 3-pin connector kit ...

Part Number: 101-0163The Link 2.5 Bar MAP sensor reads up to 2.5 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 1.5 Bar (approx 22psi) of boost pressure. The wiring pinout for this sensor is marked directly on the sensor. Includes 3-pin Deu...

Part Number: 101-0162The Link 1.15 Bar MAP sensor reads up to 1.15 Bar absolute pressure. This means it is suitable for use in naturally aspirated engines. This MAP sensor can also be used in applications where positive intake pressures of up to 0.15 Bar (approx 2 PSI) are expected (eg. Ram-air effe...

Part Number: 101-0054Donut style 8mm Knock Sensor prewired with loom, flying leads. Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Light.

Part Number: 101-00020.4m long 'A' loom to suit G4, G4 and G4X Wire-In ECUs Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is al...

Part Number: 101-00030.4m long 'B' loom to suit G4, G4 and G4X Wire-In ECUs Perfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘B’ Loom has a Link ‘B’ ECU connector at one end and unterminated wires at the other. All wires are colour coded to match the manual. This loom is al...

Part Number: 101-0045Includes 2-pin Deutsch DTM connector kit Aluminium and steel weld in mounting bosses available 1/8' NPT Thread

Part Number: 101-0048Includes Plug Kit - 2 way Bosch Style plug, terminals and boot Aluminium and steel weld in mounting bosses available (IATBMA & IATBMS)

Part Number: 101-0077Includes Plug Kit - 2 way Bosch Style plug, terminals and boot M12 Thread

Part Number: 101-0106Want to add additional inputs/output to your Link Plugin ECU? Use the XS Loom. The Link XS Loom plugs into the expansion connector on all Link G4, G4 and G4X plug-in ECUs. The number of extra inputs and outputs added by the XS Loom is dependent on the Plugin ECU. For specific de...