Vinny Fab 83 views Claim this Business♡

CAN Adaptor Loom (DTM-4 to Flying leads) - Suits AMP Superseal 1.0 series ConnectorSuits: Haltech IC-7 Dash, WB1, WB2, and aftermarket ECUs using the AMP Superseal 1.0 Series ConnectorIncludes: 1 x HT-130046 CAN Adaptor Loom (DTM-4 to Flying leads)Notes: Suits aftermarket ECUs using the AMP Superseal 1.0 Series Connector Terminated with 2 x Pins to suit connector.

CAN Adaptor Loom (DTM-4 to 6 pin Circular Connector) - Suits Dual Connector Link ECU'sSuits: Haltech iC-7 Dash, WB1, WB2 and Link Wire-in ECUs (Storm, Extreme, Fury, Thunder, Force GDI)Includes: 1 x CAN Adaptor Loom (DTM-4 to 6-pin Circular Connector)Notes: Suits Dual-Connector Link ECUs Wiring of input power required

CAN Cable - DT to DTM Adaptor- Suits CAN KeypadSuits: CAN Keypad 2 x 4 and 3 x 5Includes: 1 x HT-130045 - Adaptor HarnessNotes: CAN Cable - DT-4 to DTM-4 Adaptor- Suits CAN Keypad - 200mm

Notes: Compression ferrules are single use and must be replaced when replacing probes.

1/4" Mild Steel Weld-on Base Only

Includes: Nut and FerruleNotes: Compression ferrules are single use and must be replaced when replacing probes.

1/4" Stainless Steel Weld-on Base Only

Includes: Nut and FerruleNotes: Compression ferrules are single use and must be replaced when replacing probes.

Includes: Nut and FerruleNotes: Compression ferrules are single use and must be replaced when replacing probes.

Suits: NA or Forced induction applications. Used with a Requires a TCA 2 or 4 thermocouple amplifier.Includes: Mini K Type connector.Notes: Does not include any fitting hardware. Please order separately if required.

Suits: NA or Forced induction applications. Used with a Requires a TCA 2 or 4 thermocouple amplifier.Includes: Mini K Type connector.Notes: Does not include any fitting hardware. Please order separately if required.

Suits: NA or Forced induction applications. Used with a Requires a TCA 2 or 4 thermocouple amplifier.Includes: Mini K Type connector.Notes: Does not include any fitting hardware. Please order separately if required.

Suits: NA or Forced induction applications. Used with a Requires a TCA 2 or 4 thermocouple amplifier.Includes: Mini K Type connector.Notes: Does not include any fitting hardware. Please order separately if required.

12 Position Rotary Trim Module - (Boost/Fuel/Ign ) Dual Switch Panel Only - includes yellow knobIncludes: - Dual panel- Yellow adjustment knob- 2 x 12 position rotary trim modules

Dual Switch Panel Only - includes Yellow knobIncludes: Dual panel and yellow adjustment knob.Notes: 12 Position Rotary Trim Modules are NOT included, please order 2 x HT-010504 if required.

Plug and Pins Only 24 Pin TYCO As supplied this product is direct Plug 'n' Play compatible with an Elite ECU CAN port, Elite ECU Harness CAN connector or multiple CAN device installation using an Elite 4 Port CAN HUB. If you are connecting this product with a Platinum Pro Plug-in, Sport or Sprint EC...

The TMS-4 can fire several optional trouble codes, including: - Pressure High / Pressure Low- Temperature High - Air Leak Detected- Sensor Battery Voltage LowSuits: Haltech Nexus and Elite ECU's using NSP and ESP SoftwareIncludes: 1 x Haltech TMS-4 Receiver 1 x TE Mcon to DTM-4 CAN Cable 4 x Externa...

Wi-Fi Antenna. Glass Mount.Suits: NEXUS R5Includes: 1 x Glass Mount Wi-Fi Antenna. 1.5m lead.Notes: For increasing signal strength when standard Wi-Fi antenna is shielded by the placement of the ECU.

12 Position Rotary Trim Module - (Boost/Fuel/Ign ) Triple Switch Panel Only - includes Yellow & Red knobsIncludes: Triple panel, yellow and red adjustment knobs and 3 x 12 position rotary trim modules.

Triple Switch Panel Only - includes Yellow & Red knobsIncludes: Triple panel and yellow and red adjustment knobs.Notes: 12 Position Rotary Trim Modules are NOT included, Please order 3 x HT-010504 if required.

SurLok Connector Black 120A - Suits Nexus R3Suits: Nexus R3Includes: 1 x 120A Black SurLok Connector

Superseal connector - 34 Pin (Key 3) Plug and Pins- 34 Pin (Key 2) Plug and Pins Plug and pins only - Male Deutsch DTP-06-4S - Black connector (25Amp)Includes: Includes 1 x AMP 34 Position Connector Key1 pins 1 x AMP 34 Position Connector Key2 Pins 1 x DTP 4 Position Deutsch Connector Wedge and PinsNotes: Used to construct harness for Nexus R3 VCU's

Plug and Pin Set - Suits Nexus R5For use in converting an existing loom to suit NEXUS R5 applications.Suits: NEXUS R5Includes: 1 x AMP 34 Position Connector Key1 1 x AMP 26 Position Connector Key1 1 x AMP 34 Position Connector Key2 1 x AMP 26 Position Connector Key3 1 x DTP 4 Position Deutsch Connec...

Plug and Pins Only - Delphi 3 Pin Pressure Sensor ConnectorSuits: HT-010110 - 5 Bar TI MAP Sensor HT-010138 - 5 Bar Motorsport MAP Sensor HT-010130 - 7 Bar TI MAP Sensor HT-010904 - 150 PSI TI Pressure Sensor HT-010910 - 150 PSI Pressure Sensor HT-010906 - 250 PSI TI Pressure Sensor HT-010912 - 250 PSI Pressure Sensor HT-010908 - 2000 PSI Pressure SensorIncludes: Pack of 3 Pins.